If you have a new refrigerator, you may be wondering how to install a water line. The basic method is to connect a water shutoff valve to the fridge and then install a tee-fitting pipe from the sink to the refrigerator. This pipe should be straight and deburred on the outside. When installing the waterline, be sure to check that the refrigerator is capable of providing water.
Stainless steel is durable and strong
Stainless steel is one of the most popular materials for a refrigerator water line. It is not only durable but also flexible. However, copper tubing is prone to kink, which may block the water flow and affect the taste of the water. Stainless steel is strong enough to be a water line for a refrigerator, but it is more expensive than copper.
It is also flexible, which makes it easier to work with. Stainless steel is easier to work with than plastic. It also has a long lifespan and doesn’t cause a funny taste. While a stainless steel water line costs a bit more, it will last much longer and will outlast your refrigerator. If you’re installing a refrigerator without ice or water dispensers, you won’t need a water line. Those that don’t require plumbing can simply dispense water from a tank.
When it comes to the water line for a refrigerator, stainless steel is the best choice. It is very strong and durable, which makes it a good choice. A stainless water line won’t corrode. However, there are some concerns you should know about the material. Some water lines are made of nylon tubing. Plastic tubes can be damaged or corroded when exposed to hot water, so you should use a stainless steel water line.
SharkBites require that the outside of the pipe be deburred before insertion
Before using SharkBites, the outside of the water line for a fridge must be thoroughly deburred. To prevent a laceration or a chunk of O-ring from escaping the refrigerator, the outside of the water line should be deburred. To do this, you can use a deburring tool and a pipe cutter. Make sure to cut the pipe flush. Ensure the pipe is free of any debris or cracks, which can lead to leaks later. Also, make sure that the SharkBite fitting is free of any debris, as this can prevent the device from functioning properly.
For best results, you should deburr the outside of the water line for a fridge using a special tool. The deburring tool can also serve as a depth gauge. Then, mark the tubing with a permanent marker and proceed to insert the SharkBite. Remember, SharkBites fittings are not easy to remove without a special tool, so deburring the water line before insertion will guarantee that the water line is installed properly.
Straightening coiled tubing
When straightening coiled tubing for assembling a refrigerator, make sure to begin at the back of the appliance. This will help you avoid any kinks in the line. For ease of installation, you can drill holes between cabinets in a half-inch interval. Start by snake-in the tubing from the refrigerator to the back of the appliance. If necessary, use a tool to measure the length of the tubing.
The waterline of your refrigerator has a compression joint. To attach the waterline, remove the section of cold water pipe to solder in the 1/2-inch copper tee. If you are using CPVC (plastic) or steel pipes, use a tee fitting of the same material. If you’re unsure of how to tighten the compression joint, you can use pipe compound to make it secure.
Connecting a water shut-off valve
When connecting a water shut-off valve to s refrigerator water line, you need to make sure the appliance is unplugged from the power source. In some cases, the refrigerator shut-off valve may be inside the unit. Make sure you turn off the ice maker to avoid cycling the water valve. Then, pull the refrigerator forward to uncover the water supply line. This is where you will need to connect the shut-off valve.
Before you start connecting the shut-off valve to the refrigerator water line, you must disconnect the water supply from the waterline. This will relieve pressure. Make sure the tube is seated firmly using the rubber gasket. If your valve does not have a retaining clip, use a hammer and center punch to mark the exact location of the shut-off valve. Next, attach the blue water inlet valve to the refrigerator’s water line by loosening the nut.